google.com, pub-1990720073119592, DIRECT, f08c47fec0942fa0 electrotanya: LED TV RESET

LED TV RESET

Hard Reset Methods

Service Mode / Factory Mode Entry Procedure to different brand Televisions.
Chinese Sets

Hold down (Volume down) on set and press 'Recall' on remote.
'Recall' is the button that activates the channel number and clock onscreen.
After you have made your changes, in most cases, pressing 'POWER' on the remote will clear (Exit) the factory mode.

On some models pressing the 'AV' button will revert things to normal operation.
In rare cases, the sequence first described above (Vol - on set and recall on remote) will have to be repeated at least once more.
If none of the above methods works, try using a universal remote - best one that has a LOT of in-built models.
Search through the available models looking for any that suddenly causes the set to change channels.
Lock this setting into the remote and press '2'.
Factory mode should appear.

COBY
Enter menu, Hi-Lite “audio” then enter 8893 Mode/Source 2580 select “Other setting”, select “Shipment” then Yes
To exit the service menu “Power Off”.


Dynex
Source/Input 2580
Hold Vol down on TV and hold the (#1) button on remote, Vol will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.
Source/Input 2580 > menu 1999 (TV is on)

Element
Menu 0000 > menu 1147

Haier
Pull up menu, Hi-Lite “audio” then enter 8893.

Hisense
In customer menu go to “Parental” enter 0000 then select “Clean All”.
Power the set OFF and back ON and first time setup menu will be there.
For some models, same as above model except in menu it is labeled “Lock”.

Insignia
Input 2580 (TV is on)

LG / Zenith
Hold MENU on TV and MENU on remote for 5 to 10 seconds, then select reset option.

Mitsubishi
Menu 123 or Menu 2470 (TV is on)
NEC
While powering ON, hold "MENU" or "INPUT" on TV, depending on model. (Only disables error lock out/buffer and puts TV in temporary service mode.)
To reset to factory > on remote, Off Timer - Menu - Exit - Off Timer, then select reset option.

Panasonic
Hold [VOL--] on TV, press and hold menu button on remote.

Philips
Push Menu, select “Features” then select “Current software Info” push 062596-info on remote then push info again; red “Initialize” appears and changes color then complete.
Push power button to exit.

Polaroid
Hold [VOL--] and [CHANNEL--] or hold [VOL+] and [CHANNEL+] (TV is on)

Proscan
In customer menu go to setup, select parental control menu, enter 0000 then select “clear channel list”.

RCA
Menu 1147

Sanyo
Hold VOL Down on TV, press and hold #1 button on remote, VOL will jump to halfway and set shuts off.
Turn back on have 1st time setup screen.

Samsung
Mute 182 power (TV is off)
(On some models, Factory Reset is on this menu, on some, you must go into the “Options” submenu)
Most newer Samsung TVs have an easy to access reset method.
Press and hold the Exit Button on the Remote for at least 10 seconds until a reset screen appears.
Follow the on screen prompts to reset the TV.
Samsung (European)
Power off, Info - Menu - Mute - Power, then find factory reset and execute option.
Seiki
Menu 0000

Sharp
(Note – On Sharp models, you will need to look through the menus to find the reset option)
Menu, 1999
Menu, 3481
Menu, 1147
While holding [VOL– & INPUT] buttons on TV plug in set when “K” appears push (VOL– & CHANNEL-)
Sony
Hold “arrow up” on Remote and push power button on TV (TV is ON)
Symphony
Source/input 2580
Toshiba
On Menu, select “Installation”, then “System Information” press the right arrow button.
(“System Information” will change to “Factory Reset” or something similar) follow on-screen instructions
Vestel
Menu 4725 then select "RESET"
Vision Quest
Source / Input 2580
Vizio
In customer menu under “Help” tab is Factory Default enter 0000
[If more than one procedure is listed for a given manufacturer, try the different ones until you see which one works for your set.


SANYO
1.
* Unplug the power cable.
* Press and hold the {MUTE} button on the remote control while plugging the power cable back into the outlet.
* Keep pressing the {MUTE} button until the TV powers on with the Service Menu displayed.
* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.
* Some menus might have sub-addresses. Use the numeric buttons {0} to {7} to adjust sub-item data.
* Press the {MENU} button or turn the TV off to exit.

2.
* Unplug the power cable.
* Press and hold the {VOL -} button on the TV
while plugging the power cable back into the outlet.

* Keep pressing the {VOL -} button until
the TV powers on with the Service Menu displayed.

* Use the {CH+} {CH-} buttons to select menus.
* Use the {VOL+} {VOL -} buttons to change settings.

* Some menus might have sub-addresses. Use the
numeric buttons {0} to {7} to adjust sub-item data.

* Press the {MENU} button or turn the TV off to exit.

SHARP LCD TVs :

* While the LCD is on, unplug the power cable.
* Then while pressing the {INPUT} & {VOL -} buttons on the remote, plug the power cable back into the outlet.
* When it powers up you will see a little "k" appear in brackets.
* Then on the TV, press and hold {VOL -} & {CH -} down and release.
* The Service Menu will be displayed.
* Use {CH+} {CH -} buttons to navigate
* Use {VOL+} {VOL -} buttons to adjust the value.
* Turn the set off to exit the Service Menu.



SONY
# Using the remote control:
# Turn the TV off.
# Press {DISPLAY} {5} {VOL+} {POWER ON} buttons.
or
Press {DISPLAY} {5} {POWER ON} buttons.
# The Service Menu will be displayed.
# Use numbers {1} and {4} to select the item to adjust.
# Use numbers {3} and {6} to adjust the value of the data.
# Press {MUTE} then {ENTER} to save new settings.
# The words "WRITE" in red will show up in the upper right corner if saved.
# Turn the TV off to exit the service menu.

SONY PROJECTORS :


* Service Menu :
* Using the remote control
* Press {ENTER} {ENTER} {UP ARROW} {DOWN ARROW} {ENTER}.
* Then {UP ARROW} when it asks: "Do you want to enter the Service Mode?".

* Factory Mode :
* Using the remote control
* Press {ENTER} {ENTER} {LEFT ARROW} {ENTER}.
* Then {UP ARROW} when it asks: "Do you want to enter the Factory Mode?".

THOMSON
1.
* With the TV in standby:
* Press and hold the {VOL -} & {PRG -} buttons on the TV.
* Keep both buttons pressed until the TV turns On with the Service Menu displayed.
* To exit, turn the TV Off.

2.
* While the TV is On, press the {POWER} button on the remote control to put TV in standby.
* Turn the TV Off using the {POWER} button on the TV.
* Using the buttons on the TV:
* Turn the TV On while pressing the {PRG -} & {VOL -} buttons
* The Service Menu will be displayed.
* To exit, turn the TV Off.

TOSHIBA LCD's :


* Press the {MENU} button on the remote.
* Highlight the "Picture" icon.
* Press the {9} {3} {0} {1} buttons
on the remote control.

* The Service Menu will be displayed
with the following Modes:

"Options" - "Adjustments" - "Selections"

* Use the {OK} button to access and
navigate through these Modes.

* To change values use {VOL +} {VOL-) {P+} {P-}
* To exit, press the {MENU} button.

Tv jvc lcd hd don't turn on blue liht blinking

For Models: LT-32E479, LT-32EM49, LT-32P679, LT-42X579, LT-42SL89, LT-42EM59, LT-42P789, LT-46SL89, LT-47X579, LT-47EM59, LT-47P789, LT-52X579, LT-52P789 After the TV is powered ON, no video appears and the power LED at the lower left of the TV begins flashing:
Restore the TV's normal function by changing the operating mode. Please follow the procedure below.
PROCEDURE
• 1. Unplug the TV or remove AC power from the TV
• 2. Count to ten, then plug in the TV
• 3. Locate the [Menu], [Vol-] and [Power] button on the TV's side panel
• 4. Using the buttons on the TV's Side Panel, press and hold both the [Menu] and [Vol-] buttons.
• 5. While holding those buttons, press and release the [Power] button one time and count to 3 before releasing the [Menu] and [Vol-] buttons.
• 6. The TV's lower left Blue Power LED will come ON.
• 7. Wait 30 seconds. Confirm that the blue LED on the Lower Left of the TV (not the iPod dock for iPod models) has remained ON during this time.
a. The TV may have turned ON. If so,continue at step 12 b. If the Blue LED on the TV's Lower Left corner remained ON, continue to step 8.
• 8. After confirming that the Blue LED is ON, unplug the TV or remove the AC power from the TV.
a. If the Blue LED on the TV's Lower Left corner is flashing, restart the procedure from step 3
• 9. Count to 10, then plug in the TV
• 10. The TV power should automatically come ON but no picture will appear. Only the blue power LED will be ON
• 11. Wait 40 seconds and the TV picture should appear
• 12. When the TV picture appears, you may begin normal use of the TV. (procedure is complete)
________

No comments:

Post a Comment